Remote Battery Disconnect Switch 12/24V 240A Kill Switch Automatic Power Off Prevent Battery Drain with Remote for Car Truck SUV Features: *1. Magnetic Lock Function: The arc extending switch of this car options a new type of relay,which uses magnetic principles to control the connection and disconnection of the circuit The standby current is 0.007A, which is more energy-efficient. *2. Suitable for 12V/24V DC power vehicles.Compatible with Ford Chevrolet GMC Dodge and most sedans, trucks, RVs, trucks, trailers, etc., with displacement below 3.0L. *3. Automatic Disconnect: If the battery voltage is below 11.8V,the remote disconnect switch will automatically disconnect the power in 120 seconds to save energy. If the voltage is higher than 13.2V, the remote control will be invalid to prevent accidental disconnection of power while driving, and the power can only be controlled through the manual switch. *4. Easy Installation: The power off switch is connected to the negative pole to ensure stable performance Please remember to turn off the engine before installation. *5. Battery Protection: By using this battery switch,you can avoid unwanted battery power consumption caused by prolonged parking, good electronic devices, aging wiring, and striving to turn off lights It can effectively protect and extend the lifespan of car batteries It can effectively protect and extend the lifespan of car batteries. Product specifications and characteristics 1. Working voltage range: 6-30VDC 2. Adaptive 12V car system and 24V car system 3. Automatic alarm for low battery threshold and automatic disconnection of battery 4. Frequency 433.92MHz, matched with self-locking mode 5. Indicator light display (on and off when connected) 6. 700uA ultra-low standby power consumption 7. Driving process and ignition accidental triggering protection Product parameters 1. Working temperature -20 C to+100 C 2. Rated current of switch 240A 3. Instantaneous current of switch 500A 4. Voltage loss protection threshold 11.8V+-0.2V/23V+-0.2V 5. Power loss delay alarm for 60 seconds, automatic disconnection for 120 seconds 6. Standby current 700uA Remarks: 1. The remote control can be paired with the device normally within the working voltage range 2. Manual button ON/OFF can be used to connect and disconnect the device within the working voltage range 3. Equipment with a power supply voltage below 6V or above 30V will automatically shut down and disconnect 4. If the power supply voltage is lower than the protection threshold voltage (11.8V/23.2V) for 60 seconds, an alarm will be triggered. If the duration is 120 seconds, the equipment will automatically disconnect to protect the battery 5. Voltage higher than 13.3V (12V system)/26.2V (24V system) RF remote control failure to prevent accidental touch of remote control buttons during driving, resulting in power failure during driving 6. When the voltage range is 6-18V, it self identifies as a 12V vehicle system and operates in response to the 12V system threshold point 7. When the voltage range is between 18-30V, it self identifies as a 24V vehicle system and operates in response to the threshold point of the 24V system 8. When driving, the battery voltage is relatively high, and the system enters a false triggering protection state 9. When igniting, the battery voltage is relatively low and the system enters the ignition misoperation protection state Remote control matching instructions 1. Interlock mode (applicable to vehicle system control) - Press the manual button ON continuously for 3 seconds, and the code indicator light will flash 3 times to enter the learning mode. Press the button on the remote control, and the code indicator light will flash 3 times after successful code matching. Then press the other button on the remote control, and the code indicator light will flash 3 times after successful code matching; 2. After entering the learning mode, if the learning code indicator light does not receive a remote control signal within 30 seconds, it will automatically exit the learning mode; 3. Clear code - Long press the manual button ON to flash the code indicator light 8 times, indicating that the clear code is complete (long press the manual button ON to display the indicator light flashing 3 times, 4 times, 5 times, and 8 times in sequence; among them, flashing 3 times is the interlock mode learning state, flashing 4 times is the self-locking mode learning state, flashing 5 times is the jog mode learning state, flashing 8 times is the clear code state); 4. A set of 20 codes can be paired with 10 different remote controls simultaneously. _x000D_