Features: _x000D_ 100% brand new and high quality _x000D_ The product is used to measure the dynamic state of the liquid flowing through the pipeline, such as: water, ethylene, ethylene glycol and other liquids that have no corrosive effect on copper _x000D_ Application: water treatment system, central air conditioning, water cooling unit, fire protection system and other fields. _x000D_ Adopts premium material, with strong temperature adaptability of 0~ 120, and can withstand high pressure of 1.0Mpa. _x000D_ The flow control value is adjustable and the action repetition point is stable. _x000D_ _x000D_ _x000D_ Specification: _x000D_ Material:brass and stainless steel(body), stainless steel( Leaf blade), plastic (shell) _x000D_ Interface dimensions: 1/2"(HFS-15) _x000D_ Control mode: blade type _x000D_ Max. working pressure: 1.0Mpa _x000D_ Ambient temperature: 0C~60 _x000D_ Liquid temperature: -10~100(non-freezing) _x000D_ Micro switch: single pole double throw (SPDT) _x000D_ Contact life: 100, 000 cycles _x000D_ Electrical parameters of micro - switch: 220VAC, 15A _x000D_ Weight: Approx.407g/14.4oz _x000D_ _x000D_ _x000D_ Package list: _x000D_ 1 x flow switch _x000D_ 1 x Chinese and English operation manual_x000D_ _x000D_ 3 x paddle _x000D_ _x000D_ _x000D_ Installation and adjustment: _x000D_ 1. Open the flow switch housing; _x000D_ 2. The switch has been set at the minimum flow value when leaving the factory. Increase the flow setting value and turn the adjusting screw counterclockwise; _x000D_ 3. Press the target to check whether the micro switch can work normally. Excessive clockwise rotation of the adjustment screw may lead to the failure of the flow switch; _x000D_ 4. After the installation, please press the lever of flow switch several times to check. Once it is found that there is no "click" sound when the lever is restored, rotate counterclockwise _x000D_ Adjust the screws until there is a "click" sound; _x000D_ 5. The adjustment screw of lacquer seal is only for factory to adjust the state of flow switch. Please do not change or adjust it _x000D_ 6. Observe three working cycles, make sure that the switch and the system connected with it are in normal operation, and cover the switch shell in time. _x000D_ Matters needing attention: _x000D_ 1. Please check the flow switch carefully before installation. The package should be complete and the appearance should be free from damage and deformation. If you have any questions, please contact the manufacturer: _x000D_ 2. The flow switch can be installed in the horizontal pipe or the vertical pipe with the upward direction of liquid flow, but it cannot be installed in the pipe with the downward direction of liquid flow. Gravity should be considered when installing in piping above the flow direction of the fluid _x000D_ 3. The flow switch must be installed on the straight pipe of the section, both sides of which are short of the straight stroke of 5 letter pipe diameter. At the same time, it should be noted that the direction of liquid flow in the pipe must be consistent with the direction of arrow on the switch shell. _x000D_ 4. The HFS flow switch shall not be used in pipelines where the liquid temperature drops below the freezing point of the liquid. _x000D_ 5. The HFS flow switch cannot be hit by water. If there is a quick closing valve in the downstream of the flow switch, the throttle must be used. _x000D_ 6. When installing wiring, please pay attention to the following matters: _x000D_ * it is absolutely forbidden to impact the wrench on the switch bottom plate, resulting in deformation failure of the flow switch; _x000D_ * to avoid electric shock and damage to the equipment, cut off the power supply when wiring or debugging; _x000D_ * when wiring, it is absolutely forbidden to adjust any screws other than micro switch terminals and grounding screws. It should be noted that the micro switch wiring cannot be used _x000D_ If the force is too strong, it will easily cause the position displacement of the micro switch itself and lead to the failure of the flow switch. _x000D_ * special grounding screws must be used for wiring, and installation screws cannot be removed at will, otherwise the controller will be deformed and invalid; _x000D_ * the blade of the flow switch cannot contact with the inner wall of the pipe and other throttles in the pipe, otherwise the switch cannot be reset normally.